Ye Olde Rocket Forum

Ye Olde Rocket Forum (http://www.oldrocketforum.com/index.php)
-   RockSim Asylum (http://www.oldrocketforum.com/forumdisplay.php?f=24)
-   -   Printing Fin Patterns (http://www.oldrocketforum.com/showthread.php?t=5043)

Davidtmp 04-05-2009 08:23 PM

Printing Fin Patterns
 
I posted on TRF, didn't get a response, so I'll ask the pros here......When you print a fin template that is quite large, bigger than the paper, you have a small margin around the sheet. Do I just need to trim the margin right where the line starts and then tape the sheets together? Or does it make an overlap area? Does that make sense?

CPMcGraw 04-05-2009 08:58 PM

Quote:
Originally Posted by Davidtmp
I posted on TRF, didn't get a response, so I'll ask the pros here......When you print a fin template that is quite large, bigger than the paper, you have a small margin around the sheet. Do I just need to trim the margin right where the line starts and then tape the sheets together? Or does it make an overlap area? Does that make sense?


In RockSim 7 and 8, I believe there is a 1/2" overlap area for pattern alignment when you have to span more than one sheet. This has been eliminated in RockSim 9, however -- there is NO direct printing feature for patterns anymore. You export the SVG file, then open it up in a program like Corel Draw, where you do your editing before the final print.

James Pierson 04-05-2009 09:33 PM

Hash Marks
 
For those without a drawing program :D .

When I have printed long fin patterns in the past that print up on a two or three sheets of paper I just carefully tape them togetherafter cutting them out. The joint/intersection from sheet to sheet is the corner hash marks near the outside edges of the sheets. These hash marks are very accurate as long as your cut is. Also be careful not to crumple or shretch the paper and you should be fine. Above keep the paper flat.

Hope this poor explanation helps, JP.

James Pierson
NAR# 77907

Davidtmp 04-06-2009 12:25 AM

Thanks for the replys, it helps. You know, I think I did notice the hash marks, but there is some extra on another page that is throwing me. Oh well, I may have to get the trial of RS 9 and see how it is, I guess they are still doing trial periods. I need to learn how to use GIMP on some of this stuff. Just haven't had the time lately to work on that.

atticus 04-09-2009 12:08 AM

"In RockSim 7 and 8, I believe there is a 1/2" overlap area for pattern alignment when you have to span more than one sheet. This has been eliminated in RockSim 9, however -- there is NO direct printing feature for patterns anymore. You export the SVG file, then open it up in a program like Corel Draw, where you do your editing before the final print."

Funny, I just printed a 12" long root fin in RockSim 9. Worked the same as in RS8.

CPMcGraw 04-09-2009 12:34 AM

2 Attachment(s)
Quote:
Originally Posted by atticus
"In RockSim 7 and 8, I believe there is a 1/2" overlap area for pattern alignment when you have to span more than one sheet. This has been eliminated in RockSim 9, however -- there is NO direct printing feature for patterns anymore. You export the SVG file, then open it up in a program like Corel Draw, where you do your editing before the final print."

Funny, I just printed a 12" long root fin in RockSim 9. Worked the same as in RS8.


Funny, I just located the "Print Fin Pattern button..." :o

Wonder how it got there??? :D

I'm getting old faster than I want to. My brain used to have all of six brain cells rubbing happily. Now I'm down to five, and they're not on speaking terms anymore...

Davidtmp 04-09-2009 06:55 AM

Craig, just go with the story "They must have included it on the last update" and let it go. :chuckle:

Mark II 04-09-2009 11:16 PM

I always draw the fin patterns first, either in another program or via "analog" methods ( ;) ), and then take measurements from the drawing and translate them into plan points for the fins in RockSim. So I don't need to print fin templates from RS, because the fins are derived from printed templates already. The "Fin Designer" in RockSim is too crude and awkward to use for actually designing fins from scratch within the program itself.

MarkII

rkt2k1 04-10-2009 01:45 PM

Mark,

What other programs do you use to draw fin patterns? I agree that the fin designer is one of Rocksim's current weaknesses. It's ok, but could be better. I've tried Microsoft Visio and Google Sketch-Up with some success.

... Bill

Mark II 04-10-2009 07:20 PM

1 Attachment(s)
Quote:
Originally Posted by rkt2k1
Mark,

What other programs do you use to draw fin patterns? I agree that the fin designer is one of Rocksim's current weaknesses. It's ok, but could be better. I've tried Microsoft Visio and Google Sketch-Up with some success.

... Bill

Bill,

I use my Swiss army knife of a graphics program, The GIMP (GNU Image Manipulation Program) for Windows XP. This also happens to be the only one that I can afford... ( :D ). It is free and open-source.

From the GIMP home page:
"GIMP is the GNU Image Manipulation Program. It is a freely distributed piece of software for such tasks as photo retouching, image composition and image authoring. It works on many operating systems, in many languages."
You can download the current version (2.6.6) here.

MarkII


All times are GMT -5. The time now is 11:00 AM.

Powered by: vBulletin Version 3.0.7
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.