#21
|
|||
|
|||
As I posted yesterday I would redraw the diagrams for the Lift-Kit, for the plans are confusing. It took some time but have finished the first one. What do you all thank!
I re-drawed the image you did of the Tang barone, I hope that’s ok with you, and its to scale so it can be used as a template. I will send them all to Scott when there all finished. Last edited by Arley Davis : 04-23-2007 at 02:38 AM. |
#22
|
||||
|
||||
Quote:
I have no problems with anything that makes it easier for someone to understand how something is done. I think you've captured that
__________________
Don NAR 53455 "Carpe Diem" |
#23
|
||||
|
||||
Quote:
Vern Estes? Seriously, I had to wiki the whole 'evil twin skippy' thing. One thing I'm not is George W's twin! |
#24
|
||||
|
||||
Quote:
Arley, Am I to assume that the 2" and 2 1/8" centerline dimensions for the hole locations on the drawing should be ignored and use the 1" dimension you mentioned earlier?
__________________
Handeman TRA #09903 |
#25
|
||||
|
||||
Quote:
__________________
Don NAR 53455 "Carpe Diem" |
#26
|
|||
|
|||
Thanks for catching my mistake it would be 1-1/8”. This is one of the reasons I posted it here first because it will be no problem to change it. If you see anything that is wrong with the diagrams Please let me know so I can change them before sending them to Scott.
I will do this right now and delete the diagram and replace it with the corrected one Thanks Guy’s! |
#27
|
|||
|
|||
Here is the second Diagram of the Lift-Kit, I do not thank there are any mistakes but if you do see any please let me Know, So I can correct the mistake.
I changed the diagram on #21 as was pointed out! Last edited by Arley Davis : 04-23-2007 at 02:40 AM. |
#28
|
|||
|
|||
Here is the Third Diagram of the Lift-Kit, Once again I do not thank there are any mistakes but if you do see any please let me Know, So I can correct the mistake.
You should also know that to get the diagrams posted on this thread, that they are at a low resolution and the ones sent to Scott will Look better. Next the fin Sheet! Last edited by Arley Davis : 04-23-2007 at 02:41 AM. |
#29
|
|||
|
|||
I am trying to, At this time make up fin patterns from the small Patterns from the Products flyer that has drawings of all 3 fin types, and I hit an Impasse.
Please do not get Mad Barone put I need you to either send me a trace or post it, of one of the fins or could you take a measurement for me from the fin. From your posted Fin plan shows the Root Edge as 4-1/4”, Leading edge is 2-7/8” and the distance the fin extends gut from the root edge is 2-1/8”. I am pretty sure the fin taps on both are wrong, and the angles and Leading Edges are different. See the Image of Lift-Kit Fin Compassion below! I know by the plans and the Image of the fins being placed, that the fins are centered between the body Tube. See Image from Catalog. I sure appreciate this, and I hope I can use the fin Patterns from the Products so we all can make any one of the three Lift-Kits we wish. Lift-Kit Fin Compassion Last edited by Arley Davis : 04-22-2007 at 07:59 PM. |
#30
|
||||
|
||||
Quote:
Don't worry about upsetting me. We're here to work together to get things figured out. I can't scan the fins because they're attached already so all measurements are coming from the installed fins. Okay...here's what I've got.... The root edge is 4.25". The tip length is 2 7/8". Cord length is 2 1/8". The leading edge is 2.25". The fin is not centered on the lift kit. The leading edge is 1/2" back from the forward end of the lift kit. The front of the body slot should be about 4 3/8" from the bottom (1 5/8" from front of tube). The fin tab measurment is something I'm not sure of. I know it has to start 1 1/8" from the leading edge of the fin (because it fits against the forward centering ring of the motor mount). Now, it could be centered on the fin which would mean it would also end 1 1/8" from the rear of the fin. If the root is 4 1/4", then the fin tab length would have to be 2" long. The depth of the tab would have to be the difference between the OD of the BT50 and the OD of the BT 60 (1.637 - .976 = .661"). Now, assuming the fin tab is 2" long, the body tube slot would go from 2 3/8" from bottom of tube to 4 3/8" from bottom of tube. Does this help Arley?
__________________
Don NAR 53455 "Carpe Diem" |
Thread Tools | Search this Thread |
Display Modes | |
|
|