|
#1
|
|||
|
|||
Plan Submission Guidelines
Hey folks, I've taken on the task of organizing the plans being sent in to Scott. This is just a friendly reminder to please follow the guidelines as stated HERE. When plans come in that are scanned with these guidelines it's a snap to get them processed and passed on to Scott. When they aren't and they require some Photoshop work they get put on the backburner until I have the necessary time to do the work.
If you have any questions about the guidelines either post them here or send them directly to me in a PM. Thanks!
__________________
Quando Omni Flunkus Moritati Last edited by Ltvscout : 03-01-2023 at 10:59 AM. |
#2
|
||||
|
||||
My flatbed scanner will only do A4 (just a little bigger than 8.5x11). Most of my header cards are too long to fit. How should I handle that?
Randal
__________________
Vive Ut Vive |
#3
|
|||
|
|||
Quote:
Excellent question. Scan it in two pieces. I can merge the two together. Thanks Randal!
__________________
Quando Omni Flunkus Moritati |
#4
|
|||
|
|||
I sent some scans to you this morning, but I scanned the "header card" stuff at 150 dpi, because I cannot go at 75. 72 is the closest, and I seemed to remember that the last time I sent scans y'all wanted me to send them at 150 and that you guys would "reduce" them from there.
If you want me to re-scan the box stuff from what I sent at the 72dpi, let me know. |
#5
|
|||
|
|||
Hi ForeCheck,
I downloaed the files and they look fine. 150 is fine on the box cover. I can reduce it.
__________________
Quando Omni Flunkus Moritati |
#6
|
|||
|
|||
Quote:
I'm guessing here the same would go for Decals such as Super Nova Payloader. BAR JOHN |
#7
|
|||
|
|||
Quote:
That is correct, sir. If you would, send scans that need "joining" to the plans@rocketshoppe.com address. That would go directly to Buzz who handles that for me. Thanks.
__________________
Scott D. Hansen Ye Olde Rocket Shoppe - Your One Stop BAR Shoppe! Ye Olde Rocket Plans - OOP Rocket Plans From 38 Companies! Ye Olde Rocket Forum WOOSH NAR Section #558 |
#8
|
|||
|
|||
Estes #1311
Scott
Scans sent for #1311 John
__________________
John NAR #91135 L1 SAM #0037 |
#9
|
|||
|
|||
Since it's been almost 20 years since the original plans submission guide was published, I wanted to update it to today's standards. Note that if any scans you'd like to submit are larger than 2mb in size you'll need to send them directly to me at scott at rocketshoppe dot com.
A big thank you goes out to Earl Cagle (Earl) for helping me with this updated guide. Here is how you can help: When scanning any item, be it instruction sheets, decals, fins, face cards, centering rings, patterns, whatever, set your scanner to uncompressed TIFF. This will give you a very good quality ‘master’ scan with the least loss of detail, at given scan resolutions. While this will give you large file sizes, computer storage is very cheap today. The resultant TIFF files can then be used as a basis for ‘exporting’ smaller file sizes such as .jpg, .pdf, etc. to be sent via email or other distribution methods. For primarily ‘text’-based materials such as instruction sheets or catalogs, a second scan of the item with the file type switched to .pdf will give you a good pdf copy without resorting to a pdf generation program (many people do not have access to good pdf exporting programs or they can be tricky to use). *IF* however you are NOT adept at exporting files from a given graphics progam, then set the scanner file type to .jpg or .pdf at the outset (instead of TIFF) per the sections outlined below. And finally, USE A RULER IN YOUR SCANS to provide a proper scale for the item being scanned. For items like fins, rings, templates and decals, the ruler is invaluable and allows others to properly interpret your scanned items. Generally, the ruler is NOT needed when scanning primarily text-based items such as instruction sheets, catalogs, etc. Instruction Sheet(s): --- Set your scanning software to .pdf, 300dpi, Grayscale, if the instruction sheets are black and white; set to Color if they are in color. Front Picture Panel (Header Card): --- Set your scanning software to .jpg, 300dpi, Color. Decals: --- Set your scanning software to .jpg, 600dpi, Color. Fin Patterns, balsa fin sheets, templates, centering rings, cockpits, fin marking guides, etc.: --- Set your scanning software to .jpg, 300dpi. Generally, Grayscale is fine for these items. If there is particular ‘color coding’ or markings in the templates or guides, set scanner to Color. Again, if you are adept at exporting different file types form your favorite graphics program, always do your ‘master’ scans in uncompressed TIFF format, then do your ‘distribution’ files (.jpg, .pdf, etc.) from the master TIFF file.
__________________
Scott D. Hansen Ye Olde Rocket Shoppe - Your One Stop BAR Shoppe! Ye Olde Rocket Plans - OOP Rocket Plans From 38 Companies! Ye Olde Rocket Forum WOOSH NAR Section #558 |
Thread Tools | Search this Thread |
Display Modes | |
|
|