![]() |
|
#1
|
||||
|
||||
![]() What is the recommended way of gluing regular 24lb printer paper onto a body tube without getting wrinkles, bubbles, tearing and what not? I got spray adhesive but that stuff never seems to dry completely.
|
#2
|
||||
|
||||
![]() The only thing I have for that is white glue. The best thing I have learned is using as little as humanly possible!
___________ |
#3
|
||||
|
||||
![]() Glue one end of it perfectly straight along a line you drew on the tube. G lue this good and let it dry as said above use the least amount. Once the seam has dried. aroll the paper around the tube and put a rubber band or something to hold it tight. Let this set for a good day. This will train your paper to wrap around the tube. When ready remove rubber band and an inch or two at a time glue the paper to the tube. Use the least amount of glue you can. Like two drops and sread it on the tube then roll the paper over it. When that sets do it again. For a small tube twice is good. Once you set the paper, be careful not to rub it too much, it will tear. Then seal it with your favorite sealer. Let me know if you do it this way. Chief
![]() |
#4
|
|||
|
|||
![]() Just a question.........Have you tried thinning down the glue? First DO NOT USE SCHOOL GLUE. Use the good Elmers white glue and thin it down with 91% isopropol and mix it to the consistancy of thin snot. I would get a couple pieces of ground rod stiff enough to roll it between. That would be my first thought.
|
#5
|
||||
|
||||
![]() And use an old credit card to spread it really thin.
__________________
NAR 79743 NARTrek Silver I miss being SAM 062 Awaiting First Launch: Too numerous to count Finishing: Zooch Saturn V; Alway/Nau BioArcas; Estes Expedition; TLP Standard Repair/Rescue: Cherokee-D (2); Centuri Nike-Smoke; MX-774 On the Bench: 2650; Dream Stage: 1/39.37 R-7 |
#6
|
|||
|
|||
![]() Yes. Spread it even but very thin.
|
#7
|
||||
|
||||
![]() Quote:
Question -- Why not start with sticky-back label paper to begin with? It's about the same thickness/weight/consistency as printer paper, but with the adhesive already applied. And, you can run it through a laser printer or ink-jet printer to apply patterns, if needed. The final seal can be a drop of thin CA at the lap joint applied through one of those very tiny Teflon tubes or a squeeze-bulb applicator.
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#8
|
||||
|
||||
![]() MY adhesive of choice for glueing cardstock when there can be absolutely NO wrinkles or puckers is Alleene's Super Tacky white glue.
I use it exclusively for the aeroshrouds on vintage Quest kits (X-30, HL-20, M2Q2, Delta Clipper) and it's never failed me.
__________________
Never trust an atom. They make up everything. 4 out of 3 people struggle with math. Chemically, alcohol IS a solution. NAR# 94042 SAM# 0078 |
#9
|
||||
|
||||
![]() As you can see on this Quest Delta Clipper, I laid a heavy bead of Aleene's around the inside bottom rim of the aeroshroud, but it didn't pucker or distort the outside surface.
__________________
Never trust an atom. They make up everything. 4 out of 3 people struggle with math. Chemically, alcohol IS a solution. NAR# 94042 SAM# 0078 |
#10
|
||||
|
||||
![]() Quote:
Intersting item here - the Clipper is curently released by Quest in Germany. I saw it at Dusseldorf.
__________________
Gravity is a harsh mistress SAM 002 NAR 91005 "The complexity of living is eminently favored to the simplicity of not." |
![]() |
Thread Tools | Search this Thread |
Display Modes | |
|
|