![]() |
#1
|
||||
|
||||
![]() Several years ago I was able to buy an old hobby store's supply of Centuri 1/2A 4-5M mini motors. A couple months ago we used them to fly a really fun, NAR approved, old-motor-event with my local club (JMRC). I was cleaning up today and ran across two partial boxes of the motors and as I went to consolidate them I realized they were both the long and short Centuri mini-motors. Enclosed in the box of the newer "shorties" was a notice about the "Important Revision" to the motors. I thought it might be of interest to some of you so I am posting it here, along with some photos of the motors.
Enjoy, Steve |
#2
|
||||
|
||||
![]() They used to have blue tube.
![]() |
#3
|
||||
|
||||
![]() Quote:
I think the "Important Revision" excuse of casing supplier replacement was marketing BS to mask the fact that they had closed down the motor manufacturing in Phoenix and once again were getting motors from Penrose.
__________________
Roy nar12605 |
#4
|
||||
|
||||
![]() There was a period when Estes sued Ball Paper to continue making convolute virgin tube for them as a sole supplier.
Jerry |
#5
|
||||
|
||||
![]() Quote:
I don't doubt they had a beef with their supplier (A few apparently experimental examples of Estes mini motors made with glassine covered spiral wound tubes got into stock and out on the market and I have a couple of them). I just wonder if that's the real reason Centuri went to the shorter motor.
__________________
Roy nar12605 |
#6
|
||||
|
||||
![]() Quote:
I see only three reasons for the change: 1. Estes began making their motors again and didn't want to fool with tooling for one of the Mabels. 2. Shortened them to the "industry standard", i.e. Estes' length to be compatible with other models. 3. Decided to discontue "B" motors and shorter casings would be cheaper. I'm with you on thinking it coincided with them outsourcing again. .
__________________
I love sanding. ![]() |
#7
|
|||
|
|||
![]() Quote:
Pictures or they don't exist! ![]()
__________________
Scott D. Hansen Ye Olde Rocket Shoppe - Your One Stop BAR Shoppe! Ye Olde Rocket Plans - OOP Rocket Plans From 38 Companies! Ye Olde Rocket Forum WOOSH NAR Section #558 |
#8
|
||||
|
||||
![]() Quote:
I've probably posted them here or at TRF at one point or another, but I'll dig around.
__________________
Roy nar12605 |
#9
|
||||
|
||||
![]() Found it faster than I thought. New photos.
the date stamp says "6M171" These may have been unrelated to the casing supplier problem, but may have been when they were developing the motors in early 1971. I asked Ed Brown to confirm that they were made, but I failed to ask *when* they were made. Of course, I don't remember how these came to me. There's a part of my memory that's trying to tell me that these were from the free packs given out at NARAM 13, but I doubt they would give out booster motors when I don't think they had a two stager in their initial kit lineup (they would convert the shorty Beta and Midget kits a few months afterward, as I recall). The third picture shows the inner spiral gap. I only have two of these, so I must've flown the other two from the pack at some point.
__________________
Roy nar12605 |
#10
|
||||
|
||||
![]() Quote:
4. B motor version MIGHT have had a much higher cato rate? Not saying they did, but that is another possible reason. IIRC the MPC B size 13mm Mini-Jets had a significantly higher cato rate than the smaller ones. Though it may have been one nororious bad batch and they didn't make that many batches of B's (or the others) before MPC bailed.
__________________
Contest flying, Sport flying, it's all good..... NAR# 18723 NAR.org GeorgesRockets.com Georges'CancerGoFundMe: https://www.gofundme.com/f/help-geo...ay-fight-cancer |
![]() |
Thread Tools | Search this Thread |
Display Modes | |
|
|