Ye Olde Rocket Forum

Go Back   Ye Olde Rocket Forum > Work Bench > Building Techniques
User Name
Password
Auctions Register FAQ Members List Calendar Today's Posts Search Mark Forums Read


Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 10-02-2017, 01:24 PM
mojo1986's Avatar
mojo1986 mojo1986 is offline
Old Canuck Modeller
 
Join Date: Mar 2005
Location: Kingston, CANADA
Posts: 2,160
Default Repairing Rocket Tubes That Have Zippered Along The Seam

Once in a while you may encounter this type of damage to a favorite bird and, for whatever reason, don't want to repair the damage by shortening the rocket (for example, as in my case, where the rocket is a scale bird). This is an Estes Black Brant III. Happily, there is a technique that can save the day. I'll add the repair steps as I have time.

Incidentally, this damage cannot be reliably repaired by just glueing a 'butt weld' because the insertion of the nose cone exerts a lot of stress on the damaged area and will inevitably re-open the tear.
Attached Thumbnails
Click image for larger version

Name:  IMG_0280.JPG
Views: 47
Size:  1.03 MB  

Last edited by mojo1986 : 10-02-2017 at 01:49 PM.
Reply With Quote
  #2  
Old 10-02-2017, 01:35 PM
mojo1986's Avatar
mojo1986 mojo1986 is offline
Old Canuck Modeller
 
Join Date: Mar 2005
Location: Kingston, CANADA
Posts: 2,160
Default

Step 1:

Cut a short length of tube that's the same diameter as the rocket tube, then slit it lengthwise. Tape it firmly around the damaged area making sure that the edges of the tear fit tightly together. You may want to provide internal support when you do this ( you can just use the nose cone ).
Attached Thumbnails
Click image for larger version

Name:  IMG_0281.JPG
Views: 23
Size:  1.19 MB  Click image for larger version

Name:  IMG_0283.JPG
Views: 33
Size:  1.26 MB  

Last edited by mojo1986 : 10-02-2017 at 04:05 PM.
Reply With Quote
  #3  
Old 10-02-2017, 03:39 PM
mojo1986's Avatar
mojo1986 mojo1986 is offline
Old Canuck Modeller
 
Join Date: Mar 2005
Location: Kingston, CANADA
Posts: 2,160
Default

Step 2:

I removed the old shock cord mount (the shock cord was broken anyway) to make more room for reinforcing the tube. After that I sanded the inside of the tube to give a good clean area for glue adhesion.
Attached Thumbnails
Click image for larger version

Name:  IMG_0284.JPG
Views: 34
Size:  1.35 MB  Click image for larger version

Name:  IMG_0285.JPG
Views: 33
Size:  1.38 MB  

Last edited by mojo1986 : 10-02-2017 at 04:07 PM.
Reply With Quote
  #4  
Old 10-02-2017, 03:44 PM
mojo1986's Avatar
mojo1986 mojo1986 is offline
Old Canuck Modeller
 
Join Date: Mar 2005
Location: Kingston, CANADA
Posts: 2,160
Default

Here are the materials needed for the rest of the job...........tissue paper, thin CA and one of those ladies' nail sanding sticks.
Attached Thumbnails
Click image for larger version

Name:  IMG_0285.5.JPG
Views: 34
Size:  1.30 MB  
Reply With Quote
  #5  
Old 10-02-2017, 03:56 PM
mojo1986's Avatar
mojo1986 mojo1986 is offline
Old Canuck Modeller
 
Join Date: Mar 2005
Location: Kingston, CANADA
Posts: 2,160
Default

Step 3:

Next I glued a layer of tissue paper on the inside of the tube using thin CA. I found the easiest way to do this was to cut manageable sections of the tissue paper and then get it situated and laying flat inside the tube over the damage area. Then I ran a drop of the CA down the tube along one edge of the paper. If I was satisfied with the alignment I used a piece of small dowel to wipe away the excess glue. As soon as the glue was dry I lifted the portion of the tissue paper that was not yet glued down and ran some CA under it, then laid the tissue paper down and eliminated any bubbles under the paper. Depending on the size of the damage area it may take two or more sections of paper installed in this manner to do the repair. It's hard to see the tissue paper repair in my photo because it essentially turned clear with the CA under it (I used white paper).
Attached Thumbnails
Click image for larger version

Name:  IMG_0286.JPG
Views: 38
Size:  931.9 KB  
Reply With Quote
  #6  
Old 10-02-2017, 04:01 PM
mojo1986's Avatar
mojo1986 mojo1986 is offline
Old Canuck Modeller
 
Join Date: Mar 2005
Location: Kingston, CANADA
Posts: 2,160
Default

After that I sanded the inside of the tube and the portion of the nose cone that fits into the tube. This latter job is the only part of the procedure that I found took particular care. You need to sand the cone enough for a smooth fit in the tube but must be careful not to sand down the shoulder of the cone. This is where the sanding sticks come in handy.
Attached Thumbnails
Click image for larger version

Name:  IMG_0285.JPG
Views: 24
Size:  1.38 MB  Click image for larger version

Name:  IMG_0287.JPG
Views: 27
Size:  1.14 MB  
Reply With Quote
  #7  
Old 10-02-2017, 04:03 PM
mojo1986's Avatar
mojo1986 mojo1986 is offline
Old Canuck Modeller
 
Join Date: Mar 2005
Location: Kingston, CANADA
Posts: 2,160
Default

Et voila! A rocket that still looks stand-off good and will fly again. The tube is good and strong. I expect many flights.


Joe
Attached Thumbnails
Click image for larger version

Name:  IMG_0288.JPG
Views: 52
Size:  1.15 MB  
Reply With Quote
  #8  
Old 10-12-2017, 02:54 AM
blackshire's Avatar
blackshire blackshire is offline
Master Modeler
 
Join Date: Jan 2009
Location: Fairbanks, Alaska
Posts: 6,507
Default

Thank you for posting this! A "complementary repair" (since you had to remove the shock cord anchor; I devised the following repair [my friend Dr. Roy F. Houchin tested it and wrote the article] with scale models in mind, too) is a removable shock cord anchor (see: http://www.oldrocketforum.com/showt...able+shock+cord and http://www.apogeerockets.com/educat...wsletter231.pdf ). There is no reason why body tubes cannot be kept flight-worthy indefinitely.
__________________
Black Shire--Draft horse in human form, model rocketeer, occasional mystic, and writer, see:
http://www.lulu.com/content/paperba...an-form/8075185
http://www.lulu.com/product/cd/what...of-2%29/6122050
http://www.lulu.com/product/cd/what...of-2%29/6126511
All of my book proceeds go to the Northcote Heavy Horse Centre www.northcotehorses.com.
NAR #54895 SR
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump



All times are GMT -5. The time now is 04:16 AM.


Powered by: vBulletin Version 3.0.7
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Ye Olde Rocket Shoppe © 1998-2024