Ye Olde Rocket Forum

Go Back   Ye Olde Rocket Forum > Work Bench > Building Techniques
User Name
Password
Auctions Register FAQ Members List Calendar Today's Posts Search Mark Forums Read


Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 12-16-2007, 08:36 PM
Thruster Thruster is offline
Intermediate Rocketeer
 
Join Date: Dec 2007
Location: Long Island, New York
Posts: 92
Default Tools of the trade

What are some of the tools needed to make scratch building easier, I have the Estes tube marking tool but what are some of the other tools and tricks?
Reply With Quote
  #2  
Old 12-16-2007, 08:47 PM
stefanj stefanj is offline
Master Modeler
 
Join Date: Mar 2005
Location: Hillsboro, OR
Posts: 2,845
Default

A razor saw (Xacto or equivalent)

A square (like a ruler that goes around a corner :-)

Another lighter duty steel ruler.

Lots of rubber bands and/or cheap plastic clamps.
Reply With Quote
  #3  
Old 12-16-2007, 09:05 PM
CPMcGraw's Avatar
CPMcGraw CPMcGraw is offline
BARCLONE Rocketry
 
Join Date: Mar 2005
Location: Mobile, Alabama
Posts: 5,357
Default

Quote:
Originally Posted by Thruster
What are some of the tools needed to make scratch building easier, I have the Estes tube marking tool but what are some of the other tools and tricks?


1. A 12" steel ruler for making straight cuts with your X-Acto knife...
2. More than one X-Acto #1 knife with a fresh blade...
3. A spare pack (or two) of fresh #11 blades for your X-Acto knife...
4. 3 oz paper bathroom cups...
5. Assorted artists brushes...
6. A "T-Bar" or other aluminum sanding block...
7. An assortment of sanding papers, with a larger portion of 220-grit...
8. A can of 3M-77 spray contact adhesive...
9. A Zona saw, or a #3 X-Acto handle with fine-tooth cutting blade...
10. A set of disposable kitchen cutting mats...
11. Various mechanical pencils and fine-tip pens...
12. A pair of tri-edge rules, one Archetectural, one Engineering...
13. Numerous holding stands; wooden base with a dowel and an expended motor casing on one end, or some empty CD/DVD spindles...
14. A pack of sanding twigs -- foam strips 3/32" and 1/8" wide, 6" long, with sandpaper glued to two sides...
15. Various widths of masking tape...
16. A computer with a good graphics program (Corel Draw, Photoshop, The GIMP) to create patterns with...
17. Stack of #110 cardstock, to create templates and patterns made with your computer...
18. A decent color printer...
19. T-Pins...
20. Wax paper...
21. Various viscoscities of CA glue...
22. Small bottles of yellow glue...
23. A large bottle of yellow glue to refill the small bottles from...
24. A notebook to sketch ideas in...
25. A scrap bin, to catch bits and pieces of discarded balsa and tubing in...
26. An office "cubbyhole" shelf unit for holding your cardstock, decal sheets, etc...
27. Tack rags...
28. A good air compressor, 5-6 HP, oilless, with a good regulator...
29. Several inexpensive airbrushes for colors, and at least one or two larger detail guns for spraying primer and base whites. Don't use any gun with multiple types of paint; only use one type of paint with any one gun or airbrush to avoid gumming internally.
30. Two or three dozen fresh 1 oz jars to fit the airbrushes, and several jar adapters...
31. Paint thinners by the gallon. It's much cheaper...
32. Wooden clothespin clamps, with the wood pieces turned upside down...
33. Rubber band clamps...
34. Small one-hand "pressure/tension" bar clamps... (Perfect for us, No?)
35. Patience...
__________________
Craig McGraw

BARCLONE Rocketry -- http://barclone.rocketshoppe.com
BARCLONE Blogsite -- http://barclone.wordpress.com
BARCLONE Forum -- BARCLONE Forum

BARs helping BARs

SAM 0044
AMA 352635
Reply With Quote
  #4  
Old 12-16-2007, 09:05 PM
Thruster Thruster is offline
Intermediate Rocketeer
 
Join Date: Dec 2007
Location: Long Island, New York
Posts: 92
Default

Thanks, those are the same tools I use for the RC planes, the tube marking tool works great and is easy to use.
Reply With Quote
  #5  
Old 12-16-2007, 09:08 PM
Thruster Thruster is offline
Intermediate Rocketeer
 
Join Date: Dec 2007
Location: Long Island, New York
Posts: 92
Default

Quote:
Originally Posted by CPMcGraw
1. A 12" steel ruler for making straight cuts with your X-Acto knife...
2. More than one X-Acto #1 knife with a fresh blade...
3. A spare pack (or two) of fresh #11 blades for your X-Acto knife...
4. 3 oz paper bathroom cups...
5. Assorted artists brushes...
6. A "T-Bar" or other aluminum sanding block...
7. An assortment of sanding papers, with a larger portion of 220-grit...
8. A can of 3M-77 spray contact adhesive...
9. A Zona saw, or a #3 X-Acto handle with fine-tooth cutting blade...
10. A set of disposable kitchen cutting mats...
11. Various mechanical pencils and fine-tip pens...
12. A pair of tri-edge rules, one Archetectural, one Engineering...
13. Numerous holding stands; wooden base with a dowel and an expended motor casing on one end, or some empty CD/DVD spindles...
14. A pack of sanding twigs -- foam strips 3/32" and 1/8" wide, 6" long, with sandpaper glued to two sides...
15. Various widths of masking tape...
16. A computer with a good graphics program (Corel Draw, Photoshop, The GIMP) to create patterns with...
17. Stack of #110 cardstock, to create templates and patterns made with your computer...
18. A decent color printer...
19. T-Pins...
20. Wax paper...
21. Various viscoscities of CA glue...
22. Small bottles of yellow glue...
23. A large bottle of yellow glue to refill the small bottles from...
24. A notebook to sketch ideas in...
25. A scrap bin, to catch bits and pieces of discarded balsa and tubing in...
26. An office "cubbyhole" shelf unit for holding your cardstock, decal sheets, etc...
27. Tack rags...
28. A good air compressor, 5-6 HP, oilless, with a good regulator...
29. Several inexpensive airbrushes for colors, and at least one or two larger detail guns for spraying primer and base whites. Don't use any gun with multiple types of paint; only use one type of paint with any one gun or airbrush to avoid gumming internally.
30. Two or three dozen fresh 1 oz jars to fit the airbrushes, and several jar adapters...
31. Paint thinners by the gallon. It's much cheaper...
32. Patience...

33 An understanding wife.
Reply With Quote
  #6  
Old 12-17-2007, 12:42 AM
Tau Zero's Avatar
Tau Zero Tau Zero is offline
Incurable SEMROC Fan
 
Join Date: Mar 2005
Location: Twin Falls, Idaho, USA
Posts: 2,317
Thumbs up Rearranging Priorities

Quote:
Originally Posted by Thruster
33 An understanding wife.
Actually, you may want to scoot that one all the back up to #1.


From somebody who knows,
__________________
Jay Goemmer
"Centuri Guy"/"Tau Zero"
YORF Member 28
Semroc SAM #0029
NAR 86131


"I think about organizing things all the time. Never seems to happen. I find something that piques my interest and I'm off on a quest. Or a Centuri. "

--Bill Eichelberger, 02/22/2022


“Centuri fret buzz in an updated form.”
Bill “Wallyum” Eichelberger re: Estes Flutter-By
03 Sept 2014
Reply With Quote
  #7  
Old 12-17-2007, 07:38 AM
tbzep's Avatar
tbzep tbzep is offline
Dazed and Confused
 
Join Date: Mar 2005
Location: TN
Posts: 11,604
Default

Quote:
Originally Posted by Thruster
Thanks, those are the same tools I use for the RC planes, the tube marking tool works great and is easy to use.


There's a lot of R/C stuff that comes in handy building rockets. I did without a lot of those things until I first started doing R/C.

BTW, there's another handy little item that I haven't noticed (I only skimmed the above lists). I recently got a hobby vice and wish I had bought one years ago. I only have one problem with it....my son always has something clamped in it.

Hey, where'd my pic go? I'll try linking from Hobbico instead of Tower.


Last edited by tbzep : 12-17-2007 at 03:05 PM.
Reply With Quote
  #8  
Old 12-17-2007, 08:11 AM
Ltvscout Ltvscout is offline
Ye Olde Rocket Shoppe
 
Join Date: Jun 2004
Location: Milwaukee, WI
Posts: 6,469
Default

This is a good thread. Should I make it a sticky?
__________________
Scott D. Hansen
Ye Olde Rocket Shoppe - Your One Stop BAR Shoppe!
Ye Olde Rocket Plans - OOP Rocket Plans From 38 Companies!
Ye Olde Rocket Forum
WOOSH NAR Section #558
Reply With Quote
  #9  
Old 12-17-2007, 09:09 AM
ghrocketman's Avatar
ghrocketman ghrocketman is offline
President, MAYHEM AGITATORS, Inc.
 
Join Date: Jul 2005
Location: Nunya Bizznuss, Michigan
Posts: 13,418
Default

Item #9 of the list of items Craig put together above needs to be edited.
You need a #5 or #6 X-Acto handle for a razor saw, NOT a #3 handle....a #3 X-Acto is a gold version of the #1 with a screw-on pen-clip cap, which definitely will not accept a razor saw.
I'm not positively sure, but I don't think X-Acto even catalogues the #3 anymore but the #6 and #5 are still around.
__________________
When in doubt, WHACK the GAS and DITCH the brake !!!

Yes, there is such a thing as NORMAL
, if you have to ask what is "NORMAL" , you probably aren't !

Failure may not be an OPTION, but it is ALWAYS a POSSIBILITY.
ALL systems are GO for MAYHEM, CHAOS, and HAVOC !
Reply With Quote
  #10  
Old 12-17-2007, 10:14 AM
DaveR's Avatar
DaveR DaveR is offline
Master Modeler
 
Join Date: Apr 2006
Location: North MS
Posts: 836
Default

Quote:
Originally Posted by CPMcGraw
2. More than one X-Acto #1 knife with a fresh blade...
3. A spare pack (or two) of fresh #11 blades for your X-Acto knife...

Not a bad idea to have a small first aid kit or at least a few Band-aids handy.

Here's a couple of very handy PC tools for making marking guides, centering rings, etc.
http://www.rocketreviews.com/tool_template_widget.shtml
http://www.rocketreviews.com/freeware_rocket_suite.zip
__________________
Dave
Fire is the leading cause of fire.
Was once SAM#0132
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump



All times are GMT -5. The time now is 04:52 AM.


Powered by: vBulletin Version 3.0.7
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Ye Olde Rocket Shoppe © 1998-2024