Ye Olde Rocket Forum

Go Back   Ye Olde Rocket Forum > Work Bench > Building Techniques
User Name
Password
Auctions Register FAQ Members List Calendar Today's Posts Search Mark Forums Read


Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 05-16-2013, 03:04 PM
K'Tesh's Avatar
K'Tesh K'Tesh is offline
Seagulls Beware...
 
Join Date: Apr 2013
Location: Subject to Change
Posts: 930
Question How do you prepare your plastic nose cones?

I've had a mixed bag of results with this method (more success than failures), so I'm looking to see what others are doing.

For my blown plastic nose conses from my Estes kits, I first sand with 220 grit in a circular pattern to get rid of the seam lines. Then completely sand the entire nosecone until all the gloss/semigloss of the virgin plastic is gone. Next I sand again using 320 grit to eliminate the deep scratches that 220 leaves behind. Then it's onto 400 grit (wet or dry). I last use 600 grit (wet or dry) to really make things really smooth.

I'm next using toothpaste to give it one last abrasion before washing it with soap and water. I dry it, then (presuming that it's not the same color as the body tube) paint it with the final color. If it is the same color as the body tube, I'll spray a coat of primer before doing the top color.

3 of my last 4 nose cones turned out looking pretty sharp (all of them were a contrasting color to the the body tube) The last one however had odd dimples in the paint that I think may have been caused by a small amount of water (or droplets from a sneeze) that I need to get out.

To paint, I'm using some poster putty to secure the nose cone to a dowel, and painting it in its entirety (rather than masking off the shoulder). I leave the nosecone on the dowel (parallel to the ground) for as much as a day to allow the paint to dry; especially if it's a gloss color.
__________________
.
.

Dreaming of making the rockets I dreamed of as a kid (and then some).

"The Guide says there is an art to flying", said Ford, "or rather a knack."
"The knack lies in learning how to throw yourself at the ground and miss."


Launching is Optional... Landing? That Depends on Trees.

Last edited by K'Tesh : 05-16-2013 at 03:40 PM.
Reply With Quote
  #2  
Old 05-16-2013, 03:13 PM
stefanj stefanj is offline
Master Modeler
 
Join Date: Mar 2005
Location: Hillsboro, OR
Posts: 2,847
Default

I use the edge of a sharp knife to get rid of the seams.

Wet sand with really fine sandpaper.

Sludgy paint-on enamel to deal with the seams. Sand again.

I use polishing compound rather than toothpaste, but it is basically the same stuff . . . just cheaper.
__________________
NAR #27085 - Oregon Rocketry - SAM
Reply With Quote
  #3  
Old 05-17-2013, 09:04 AM
ghrocketman's Avatar
ghrocketman ghrocketman is offline
President, MAYHEM AGITATORS, Inc.
 
Join Date: Jul 2005
Location: Nunya Bizznuss, Michigan
Posts: 13,443
Default

I rarely use plastic cones, but when I do I wash them in really hot water and Cascade, then I wipe them down LIGHTLY with Dope thinner (not enough to melt/craze them), lightly sand with ultra fine sandpaper (600), then prime & paint.
__________________
When in doubt, WHACK the GAS and DITCH the brake !!!

Yes, there is such a thing as NORMAL
, if you have to ask what is "NORMAL" , you probably aren't !

Failure may not be an OPTION, but it is ALWAYS a POSSIBILITY.
ALL systems are GO for MAYHEM, CHAOS, and HAVOC !
Reply With Quote
  #4  
Old 05-17-2013, 09:42 AM
foamy's Avatar
foamy foamy is offline
Master Modeler
 
Join Date: Jan 2011
Location: The Land of Pleasant Living
Posts: 1,115
Default

Not that I'm any whiz-bang, but I just sand the bugger with 400 grit or whatever—doesn't make a lot of difference to me, fill and sand any seams, wipe with alcohol (no, I don't use my rum) and go ahead and prime it with the rest of the rocket. I figure it gives the paint something nice to grip on to. Sand as usual with the rest of the rocket.
__________________
Retro-grouch
Reply With Quote
  #5  
Old 05-17-2013, 11:40 AM
ghrocketman's Avatar
ghrocketman ghrocketman is offline
President, MAYHEM AGITATORS, Inc.
 
Join Date: Jul 2005
Location: Nunya Bizznuss, Michigan
Posts: 13,443
Default

Foamy-
I like the Alcohol wipe idea better than my use of Dope thinner; no chance of the Alcohol attacking the plastic...I think I will switch.

What kind of alcohol are you using ?
Denatured (Ethanol) Alcohol, Methanol, or Isopropyl (which does not sound good unless of the fairly uncommon 99% variety) ?
__________________
When in doubt, WHACK the GAS and DITCH the brake !!!

Yes, there is such a thing as NORMAL
, if you have to ask what is "NORMAL" , you probably aren't !

Failure may not be an OPTION, but it is ALWAYS a POSSIBILITY.
ALL systems are GO for MAYHEM, CHAOS, and HAVOC !
Reply With Quote
  #6  
Old 05-17-2013, 01:12 PM
foamy's Avatar
foamy foamy is offline
Master Modeler
 
Join Date: Jan 2011
Location: The Land of Pleasant Living
Posts: 1,115
Default

Denatured if I have it, Isopropyl (91%) if I don't.

I usually grab a mayo jar of denatured at the boat barn as that's what we use to prep surfaces before caulking and mounting hardware or painting. The isopropyl works fine too, but you have to let it dry for a bit before you paint as it's not as quick to evaporate as the denatured.

Speaking of the boat barn, "Flyer" will see the sunshine for the first time in over two and a half years this coming Tuesday. I'll post a pic in Free for All when I can. We're quite proud of her.
__________________
Retro-grouch
Reply With Quote
  #7  
Old 05-17-2013, 03:00 PM
Pem Tech's Avatar
Pem Tech Pem Tech is offline
Retromaniac
 
Join Date: Oct 2008
Posts: 298
Default

I like my nose cones lightly brazed in butter with a cream sauce.
__________________
Layne Pemberton NAR# 83083
Mad Scientist, Minion and Owner
PembertonTechnologies.com
P.O. Box 250760
North Little Rock AR, 72225

L1 on Pem-Tech Space Ark
at NSL2007

pem_tech (at) Yahoo (dot) com
TRF (at) pembertontechnologies (dot) com
Reply With Quote
  #8  
Old 05-17-2013, 05:14 PM
Chas Russell's Avatar
Chas Russell Chas Russell is offline
Retired Missile Technician
 
Join Date: Mar 2005
Location: Fort Worth, TX
Posts: 1,076
Default

Yes, but Lanye, do you deglaze the pan before plating the nose cone?

I sand with 320 grit after filling the seam and then wipe with isopropyl alcohol. Working a nose cone from the reissued Estes Maxi Honest John from years back. Seems that the seams are deeper than I remember. Been using the Tamiya white putty since I can get it at Hobby Lobby with the coupon.

Last built a Maxi HJ back in the mid-70s and flew it on F100s, E60s (successfully), and an AVI Gold Series E11.8-4.25. Lost it in 1994 at the Bonneville Salt Flats on a prototype NCR E20. Up part was good, but no ejection firing. Durn that salt is hard. Have one more reissue and two original issues.

Chas
__________________
Charles Russell, MSgt,USAF (ret.)
NAR 9790, Lvl 1
SAM "Balls Three"
Reply With Quote
  #9  
Old 05-17-2013, 06:48 PM
hcmbanjo's Avatar
hcmbanjo hcmbanjo is offline
When Pigs Fly!
 
Join Date: Sep 2005
Location: Orlando, FL
Posts: 1,102
Default

In addition to the white Tamiya filler, I've had great luck seam filling the plastic seams with the cheap, medium CA from the Dollar Tree store.

http://modelrocketbuilding.blogspot...-nose-cone.html

It stays on the plastic and sands glass smooth.
__________________
Hans "Chris" Michielssen
Old/New NAR # 19086 SR

www.oddlrockets.com
www.modelrocketbuilding.blogspot.com
http://www.nar.org/educational-reso...ing-techniques/
Your results may vary
"Nose cones roll, be careful with that."
Every spaceman needs a ray gun.
Look out - I'm the Meister Shyster!
Reply With Quote
  #10  
Old 05-17-2013, 09:39 PM
modeltrains's Avatar
modeltrains modeltrains is offline
Intermediate Rocketeer
 
Join Date: Apr 2013
Location: Farm burg along Missouri River
Posts: 54
Default

Plastic nose cones get similar treatment to plastic models:
Wash with old really soft toothbrush usinf either dish detergent or mild abrasive household cleaner.
Scrape/file/sand/fill molding seam marks with Squadron White putty.
(wonder if Hobby Lobby over in city here carries Tamiya putty?)
Sand and rinse.
Prime. Unlike plastic models, nose cones get DupliColor car primer.
for painting I mask off shoulder then tape cone to dowel, tube, stick, something to hold it.
somewhere along the way something got me started painting nose cone bases in colors which look like greenish or yellowish zinc chromate primer. Why? Dunno, just enjoy doing so.
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump



All times are GMT -5. The time now is 12:33 PM.


Powered by: vBulletin Version 3.0.7
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Ye Olde Rocket Shoppe © 1998-2024