|
#1
|
||||
|
||||
A Place For My Stuff...
This thread is a "catcher's mitt" for those designs in the new catalog that are missing RKT files and JPG images. It's just a place-holder thread for these rockets, so it's not open for general posts or other designs. Thanks.
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#2
|
||||
|
||||
Test Rocket C (2009)
Just a very basic 18mm rocket with a payload section.
Length: 28.00" Diameter: 1.17" (ST-11) Fin Span: 5.17" Weight: 1.42 oz A8-3......194'......Dv 4 FPS B4-4......462'......Dv 7 FPS B6-4......468'......Dv 12 FPS C6-5......990'......Dv 12 FPS All engines reach safe flight V on a 36" x 1/8" standard rod. Fin sheet included below. Enjoy!
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#3
|
||||
|
||||
4" Rhemus
A 4" upscale of my Rhemus, created by Fore Check back on September 5, 2007.
Length: 63.75" Diameter: 4.00" (LOC 3.9") Fin Span: 19.39" Weight: 62.75 oz As designed, the model uses engine-based deployment charges instead of electronics. The simulation results below reflect this method of deployment. I284W-10.........2924'.........Dv 21 FPS.........48" guide required I300T-10.........2346'.........Dv 40 FPS.........48" guide required I354FJ-10........2829'.........Dv 32 FPS.........60" guide required I366R-10.........2814'.........Dv 29 FPS.........48" guide required Launch lugs are not shown in the plan. Use whichever method suits your preferences. Fin sheet patterns included (next post). Enjoy!
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#4
|
||||
|
||||
4" Rhemus Fin Sheets
Two sheets, 3/16" A/C plywood. One sheet 12" x 48". One sheet 12" x 40".
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#5
|
||||
|
||||
Loadmaster "A"
This was the first version of the Loadmaster, and which for some reason never got posted. It differs from the "B" version only in the nose cone. I used an elliptical cone for the "A".
Length: 18.81" Diameter: 0.908" (ST-8) Fin Span: 4.43" Weight: 1.15 oz A8-3.......232'......Dv 5 FPS B4-4.......506'......Dv 8 FPS C6-5......1021'......Dv 4 FPS The B6-4 is not recommended. All engines reach safe flight V on a 36" x 1/8" launch rod. The fin sheet is the same as in the "B" version. Enjoy!
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#6
|
||||
|
||||
Lightning Bug (2005)
A two-stage design from April 6, 2005.
Length: 18.30" Diameter: 0.759" (ST-7) Fin Span: 3.26" Weight: 0.96 oz A10-0T/A3-4T......812'......Dv 26 FPS......36" x 1/8" launch rod Streamer recovery. Enjoy!
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
Thread Tools | Search this Thread |
Display Modes | |
|
|