#1
|
|||
|
|||
Thrustline Aerospace F-24 Panther Plans
The link below will take you to the plans for the F-24 Panther kit.
Each plan set also includes a RockSim file for the kit. That's a good thing since nowhere could I find a parts list of tubing type, length, etc. I'd appreciate it if someone with RockSim or OpenRocket will give me a hand by adding a reply to this post listing the parts type/size you extract from the RockSim file. If you could include the templates from the RockSim file I'd appreciate that as well. http://www.oldrocketplans.com/tla/TLA_F-24_Panther.zip These Thrustline Aerospace plans are for PERSONAL USE ONLY! John Rowan-Stern and Thrustline Aerospace reserves all commercial use rights.
__________________
Scott D. Hansen Ye Olde Rocket Shoppe - Your One Stop BAR Shoppe! Ye Olde Rocket Plans - OOP Rocket Plans From 38 Companies! Ye Olde Rocket Forum WOOSH NAR Section #558 |
#2
|
||||
|
||||
Scott,
Attached below is the data for the Thrustline Aerospace F24 Panther from the RockSim file: TLA F24 Panther Parts Nose cone Estes - Estes - PNC-55AC, Material: Polystyrene PS Nose shape: Hollow Ogive, Len: 5.4030 In., Dia: 1.3250 In. Wall thickness: 0.1250 In. Body insert: OD: 1.2000 In., Len: 0.5000 In. Body tube Estes - EST 3087 - BT-55, Material: Paper OD: 1.3250 In. , ID: 1.2830 In. , Len: 17.0000 In. Custom Fin set - 2 fins Custom, Material: Balsa (0.125" thick) Radial angle 0 degrees Point List in mm : 122.845480638039, 0. 105.489495692046, 69.3311937212273 107.417938463822, 136.344580040478 72.2238578788929, 145.986793899362 0., 0. Custom Fin set - 2 fins Custom, Material: Balsa (0.125" thick) Radial angle 0 degrees Point List in mm : 64.5050191406548, 0. 65.5206576016314, 16.7700114747567 74.2805393275543, 56.3799114528424 41.9070633839265, 67.1710701007184 0., 0. Custom Fin set - 1 fin Custom, Material: Balsa (0.125" thick) Radial angle 90 degrees Point List in mm : 221.27572716166, 0. 247.843311604138, 53.4508067986595 223.741368416202, 53.0803183585653 186.996140874188, 21.253743322175 0., 0. Body tube Estes - EST 3085 - BT-20, Material: Paper OD: 0.7360 In. , ID: 0.7100 In. , Len: 2.7500 In. Location: 14.2500 In. From the front of Body tube Engine block Estes - 30162-2 - Eng. block BT-20, Material: Paper Engine blockOD: 0.7100 In., Hole #1: : 16.5300 In. Len: 0.1969 In. Location: 0.0000 In. From the front of Body tube Parachute - Custom, Material: Mylar 1 parachute, Shape: 6 sided Dia: 14.9098 In., Spill hole: 0.0000 In. Engine hook Estes - Engine hook - Standard size, Material: Mass: 0.0494 Oz. eyelet - Custom, Material: Mass: 0.0100 Oz. Mass object - Custom, Material: Mass: 0.3000 Oz. Custom Fin set - 1 fin Custom, Material: Balsa (0.125" thick) Radial angle -45 degrees Point List in mm : 101.335488226224, 0. 114.749256876695, 31.8222817896545 101.315997545064, 31.8222817896545 0., 0. Launch lug Apogee - "1/8"" X 1" - , Material: Paper OD: 0.1720 In., ID: 0.1560 In., Len: 0.5000 In., Loc: 7.3750 In. Launch lug Apogee - "1/8"" X 1" - , Material: Paper OD: 0.1720 In., ID: 0.1560 In., Len: 0.5000 In., Loc: 14.2500 In. Custom Fin set - 1 fin Custom, Material: Balsa (0.125" thick) Radial angle -135 degrees Point List in mm : 101.335489563852, 0. 114.749258391385, 31.8222822097086 101.315998882435, 31.8222822097086 0., 0.
__________________
Bruce S. Levison, NAR #69055 Last edited by teflonrocketry1 : 02-19-2019 at 07:50 PM. |
#3
|
|||
|
|||
Instructions, parts list, fin templates and marking guides are also on YORP.
__________________
I like the unusual, the off beat, the avant-garde. No 3/4 FNC for me! |
Thread Tools | Search this Thread |
Display Modes | |
|
|