#41
|
||||
|
||||
Quote:
Carl, I seem to have one of these sim'd up, from back in January 2007. I thought they had been posted here... somewhere... I'm looking them over now, and it's obvious they were done pre-RS9. I'll rework the pods and post the file tonight...
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#42
|
|||
|
|||
Quote:
What do you think? It is in my logo, isn't it?
__________________
Scott D. Hansen Ye Olde Rocket Shoppe - Your One Stop BAR Shoppe! Ye Olde Rocket Plans - OOP Rocket Plans From 38 Companies! Ye Olde Rocket Forum WOOSH NAR Section #558 |
#43
|
||||
|
||||
Quote:
I have attached a working file. It includes the new BC-2031 which is a balsa replacement for the original balsa and paper cone. It is a little more complex than the original or the plastic cones. I also have the BC-711 cones on a pod.
__________________
Carl McLawhorn NAR#4717 L2 semroc.com |
#44
|
||||
|
||||
Quote:
__________________
Carl McLawhorn NAR#4717 L2 semroc.com |
#45
|
|||
|
|||
Quote:
Ya, and since it appears Ray has fallen off the face of the earth, you may as well put out that Skydart as well!
__________________
Scott D. Hansen Ye Olde Rocket Shoppe - Your One Stop BAR Shoppe! Ye Olde Rocket Plans - OOP Rocket Plans From 38 Companies! Ye Olde Rocket Forum WOOSH NAR Section #558 |
#46
|
||||
|
||||
Carl (and all...),
Here's a simulation run for the RKT file you posted earlier. I finished it up with fins and what-knots... --Data Specs-- Weight: 3.47 oz Length: 22.624" Empty margin: 8.86 B6-2.......157'......Dv 19 FPS......60" launch guide C6-3.......447'......Dv 30 FPS......60" launch guide D10-5.....1057'......Dv 22 FPS......24" launch guide Note the launch guide requirements. It needs at least a D (or a core-burner C) to get off the pad cleanly.
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#47
|
||||
|
||||
FWIW...
The earlier plan I mentioned was from 2007, and it did not work. The sim would continuously NAN out on me, meaning there was something about the configuration that RockSim was crashing on. However, I managed to use the fins and pod supports from that file to finish this one.
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#48
|
||||
|
||||
When the .010" thickness of the wrap is entered, it drops to about 39" rod. Strange. Now I am just going to have to build one!
Thanks Craig for all your work on this. Sure saved me a few hours.
__________________
Carl McLawhorn NAR#4717 L2 semroc.com |
#49
|
|||
|
|||
Quote:
We can only hope!!!
__________________
Got a Caribbean soul I can barely control..... |
#50
|
|||
|
|||
Launched my Orion clone yesterday on a B6 -2 with a moderate breeze (~5 mph), using a standard 3' rod. Nice straight trajectory, with an altitude just over 100'.
__________________
Up next: Under construction: Under repair: In finishing: Centuri Sabre clone In primer: In paint: Ready for decals: Bill Cooke NAR #31312 TRA #19705 SAM #0001 Huntsville, AL My rocket blog My rocket fleet |
Thread Tools | Search this Thread |
Display Modes | |
|
|